Short version, I changed a pipe into something I like better than what it was. Pics at end.
They say you can’t polish a turd, but I think I have come close. I bought a group of three pipes from an eBay seller recently. I was only interested in two of the pipes, and made my bid based on that. I am very happy with the two other pipes, but I still had this other one left. I couldn’t bring myself to pitch it, so I decided to try and make something of it I might like. The pipe had a Grabow stem, but I’m not so sure it was original to the pipe, it seemed to be a slightly bigger diameter.
A previous owner had applied some kind of a finish to the pipe, and it appears to have been applied with a mop. Very uneven, you could see then brush strokes. Also the end of the shank had been over-buffed and was rounded off. There were several fills in the pipe, and they were black. The only marking on the pipe said “Imported Briar”.
First thing I did was use a combination of steel wool and sanding pads to remove that awful finish. It took some elbow grease to get all of that crap off of the pipe. Then I took a chance and tried to sand back the shank end to remove the rounded over edges. I thought this might serve two purposes: to remove the rounded edge and also take it back to where the shank was a bit thicker so it would match up with the stem better. I surprised myself a bit when it worked. The stem fit isn’t perfect, but it’s pretty good. Definitely much better than before.
At this point I knew I would have to do something about those ugly fills. I decided to do a little rustification. No one is going to hire me to start doing this professionally, but I am satisfied with how it came out.
Finally, I cleaned up the stem near the button (it was in good shape otherwise) and polished the whole thing.
You can’t polish a turd, but you can make it into a knock-around-the-yard pipe.
Pics below. I always forget to take a before shot, so I grabbed some pics from the eBay sale. I think it looked worse in person than the pictures show.
Before:
These are after I started removing that finish:
Here it is now:
The pipe still has no real monetary value, but I might just get some use out of it now!
They say you can’t polish a turd, but I think I have come close. I bought a group of three pipes from an eBay seller recently. I was only interested in two of the pipes, and made my bid based on that. I am very happy with the two other pipes, but I still had this other one left. I couldn’t bring myself to pitch it, so I decided to try and make something of it I might like. The pipe had a Grabow stem, but I’m not so sure it was original to the pipe, it seemed to be a slightly bigger diameter.
A previous owner had applied some kind of a finish to the pipe, and it appears to have been applied with a mop. Very uneven, you could see then brush strokes. Also the end of the shank had been over-buffed and was rounded off. There were several fills in the pipe, and they were black. The only marking on the pipe said “Imported Briar”.
First thing I did was use a combination of steel wool and sanding pads to remove that awful finish. It took some elbow grease to get all of that crap off of the pipe. Then I took a chance and tried to sand back the shank end to remove the rounded over edges. I thought this might serve two purposes: to remove the rounded edge and also take it back to where the shank was a bit thicker so it would match up with the stem better. I surprised myself a bit when it worked. The stem fit isn’t perfect, but it’s pretty good. Definitely much better than before.
At this point I knew I would have to do something about those ugly fills. I decided to do a little rustification. No one is going to hire me to start doing this professionally, but I am satisfied with how it came out.
Finally, I cleaned up the stem near the button (it was in good shape otherwise) and polished the whole thing.
You can’t polish a turd, but you can make it into a knock-around-the-yard pipe.
Pics below. I always forget to take a before shot, so I grabbed some pics from the eBay sale. I think it looked worse in person than the pictures show.
Before:
These are after I started removing that finish:
Here it is now:
The pipe still has no real monetary value, but I might just get some use out of it now!