Repair & Treatment for Cantankerous Pipe

Log in

SmokingPipes.com Updates

Watch for Updates Twice a Week

PipesMagazine Approved Sponsor

PipesMagazine Approved Sponsor

PipesMagazine Approved Sponsor

PipesMagazine Approved Sponsor

PipesMagazine Approved Sponsor

Status
Not open for further replies.

Ziggywm

Can't Leave
Sep 9, 2019
358
3,812
Fargo, ND
The most cantankerous pipe in my collection of more than a hundred briars and meerchaums is a Savinelli de Luxe 804 Ex, a Canadian sandblast that because of its long shank (5 1/4" - 7" with bit) caught my eye in the 70s. This pipe has never "broken in". Well some time ago I cracked the shank and put it in my pipe cabinet drawer with RIP on my lips. This forum on repairs got me thinking about it, so here goes: 1) I cut the shank off below the crack. 2) I turned a replacement piece of briar and machined a tenion to fit the shank and a mortice to fit the bit. 3) After the expoxy set the tenion, I used my French wheel on the lathe to blend it in. 4) I then rusticated and stained (alcohol analine stains) the shank. 5) To address its cantankerous smoking qualities I began by salting the bowl after a reaming to wood with iodine free salt and 100 proof grain alcohol for 24 hrs. 6) I oil cured the pipe using Walnut oil and my microwave all afternoon, bringing the oil to a boil until it had pentetrated to the outside of the bowl. 7) Cleaned out the oil and let the pipe set all night. 8) Today, I filled the bowl with 20210115_103322_compress22.jpg20210114_155740_compress45.jpg20210115_134336_compress65.jpg20210115_153230_compress0.jpg20210117_144249.jpgMac Baren's Club Blend and lit it up. 9) I'm ??? smiling. I think I finally exorcised the demon sap out of this pipe!
 

Ziggywm

Can't Leave
Sep 9, 2019
358
3,812
Fargo, ND
Looks good man but I probably would have just made a new mortise where it broke.
I would have had to spin the shank to do it well. Impossible to mount a pipe of that size and zero it in. Much easier to turn a piece of briar and fit it to the pipe. Plus, I wanted to replace what I cut off; I like the length of this Canadian, otherwise I would have crushed it years ago. Savanelli also used weird size (mm?) mortises. As close as I could get were letter drill bits- took awhile to properly fit the bit tenon in the new briar.
 

Ziggywm

Can't Leave
Sep 9, 2019
358
3,812
Fargo, ND
Ziggy, great job on the repair! Seems a bit unconventional but awesome! I hope you enjoy it!
Well, it could have been silver banded, but you have to have the material. You can get them from some supply houses, but you usually have to buy a large quantity of sizes - good if you are in the pipe repair business. I could have turned a lucite or vulcanized flange and put a military mount bit in it, but I felt that would change the pipe too drastically. Plus, if you are going to mortise on a military mount, why not just replace the offending briar. I used no metal insert - it would attract moisture. And the tenon on the briar replacement matched the depth of the mortise in the shank so there would be no gap to cause turbulence in smoke, as well as become a tar pit. I drill all my draw holes at 10mm which is large, but cuts down on turbulence causing a wet pipe. Really, I think my repare quite conservative. The problem is, if you had to pay for 4 hrs @ $20 per (cheap, really) you might as well put it in a new pipe.
 

jhowell

Part of the Furniture Now
Jul 25, 2019
669
1,056
71
Phoenix, Arizona
Well, it could have been silver banded, but you have to have the material. You can get them from some supply houses, but you usually have to buy a large quantity of sizes - good if you are in the pipe repair business. I could have turned a lucite or vulcanized flange and put a military mount bit in it, but I felt that would change the pipe too drastically. Plus, if you are going to mortise on a military mount, why not just replace the offending briar. I used no metal insert - it would attract moisture. And the tenon on the briar replacement matched the depth of the mortise in the shank so there would be no gap to cause turbulence in smoke, as well as become a tar pit. I drill all my draw holes at 10mm which is large, but cuts down on turbulence causing a wet pipe. Really, I think my repare quite conservative. The problem is, if you had to pay for 4 hrs @ $20 per (cheap, really) you might as well put it in a new pipe.
Those skills go for a lot more than $20 an hour my friend.
 

Ziggywm

Can't Leave
Sep 9, 2019
358
3,812
Fargo, ND
Those skills go for a lot more than $20 an hour my friend.
Yes they do. Look at my bar cabinet I built in my shop. There is not a piece of particle board or compressor nails in this piece - all Qtr. Sawn Oak. A close friend asked what it would cost to make him one. When I quoted him $6K he swallowed hard and said "no thanks". You are lucky if you can get $20/hr.20210119_162458_compress54.jpg
 

ChuckMijo

Part of the Furniture Now
Sep 26, 2020
775
2,355
Yes they do. Look at my bar cabinet I built in my shop. There is not a piece of particle board or compressor nails in this piece - all Qtr. Sawn Oak. A close friend asked what it would cost to make him one. When I quoted him $6K he swallowed hard and said "no thanks". You are lucky if you can get $20/hr.View attachment 61001
As a fellow wood worker, that’s fantastic work!!
 
  • Like
Reactions: Ziggywm
Status
Not open for further replies.