Pipes Magazine » Pipe Talk

1. 

   990rick
   

   Junior Member
   Joined: Mar 2011
   Posts: 76

   offline

   Login to Send PM

   I just received two nice-looking Stanwells, but they draw a little hard. The hole going into the bowl on each is noticeably small. The small end of a tapered pipe cleaner will just poke into the bowl and a non-tapered bristle pipe cleaner won't go through at all. If it's not just carbon build-up I'm tempted to bore out the hole to make for an easier draw. Anyone know of any reason why I shouldn't do this? Or have any advice on just how I should? Thanks.

   Posted 1 year ago #
2. 

   jasongone
   

   Preferred Member
   Joined: Mar 2011
   Posts: 604

   offline

   Login to Send PM

   if it's straight i would assume you could do this with a drill bit but just turning it by hand, or with pliers or so forth...???

   Posted 1 year ago #
3. 

   unclearthur
   

   Preferred Member
   Joined: Mar 2010
   Posts: 7,639

   offline

   Login to Send PM

   Definitely by hand. Far too easy to screw up and ventilate a perfectly good pipe.

   If at first you don't succeed you are running about average.

   Posted 1 year ago #
4. 

   bytor
   

   Senior Member
   Joined: Jan 2010
   Posts: 369

   offline

   Login to Send PM

   Here are a couple of additional ways to hold and turn a drill bit by hand... I have found that pliers are sometimes difficult to use as they don't get a very good bite on a hard, smooth drill bit.

   T-Handle Tap Holder

   Keyless Hex-Drive Drill Chuck

   Generally a good idea to use a few sizes of bits to gradually increase the diameter of the hole (rather than trying to stuff the final size drill through the first time). The drill bits will be more likely to follow the existing hole and reduce the risk of damage.

   Posted 1 year ago #
5. 

   jasongone
   

   Preferred Member
   Joined: Mar 2011
   Posts: 604

   offline

   Login to Send PM

   tap holder! damnit. that makes so much sense.
   just a why didn't i think of that moment.

   Posted 1 year ago #
6. 

   bytor
   

   Senior Member
   Joined: Jan 2010
   Posts: 369

   offline

   Login to Send PM

   Happens to the best of us!

   Posted 1 year ago #
7. 

   cortezattic
   

   A part of the problem since he ...
   Joined: Nov 2009
   Posts: 4,406

   offline

   Login to Send PM

   It's a little out of my field, but I think a pin vice is the proper tool "for securely
   holding small stock, taps, drills, reamers, scribers, wire, small files, and other tools".
   .
   

   I find myself sitting idly on the line dividing past and future,
   as if I could kill time without injuring eternity. -- Thoreau

   Posted 1 year ago #
8. 

   990rick
   

   Junior Member
   Joined: Mar 2011
   Posts: 76

   offline

   Login to Send PM

   The pin vises look like just the ticket. I found a good set of 4 at Sears and should have them sometime next week. Thanks again everybody. You guys are terrific!

   Posted 1 year ago #
9. 

   unclearthur
   

   Preferred Member
   Joined: Mar 2010
   Posts: 7,639

   offline

   Login to Send PM

   Always happy to share what little I know. One more small item. Start with the smallest bit that will pass and work your way up slowly. Don't try to do it all in one shot.

   Posted 1 year ago #
10. 

    nmbigfoot02
    

    Member
    Joined: May 2011
    Posts: 140

    offline

    Login to Send PM

    I second the advice to work up the hole size. I did the same for a basket pipe I have that gurgled terribly. I reamed it out to 5/32" and now it smokes like a completely different pipe.

    Posted 1 year ago #
11. 

    unclearthur
    

    Preferred Member
    Joined: Mar 2010
    Posts: 7,639

    offline

    Login to Send PM

    5/32 is about optimum in my opinion. Seems to really work out well.

    Posted 1 year ago #
12. 

    portascat
    

    Preferred Member
    Joined: Jan 2011
    Posts: 911

    offline

    Login to Send PM

    Or, you can be adventurous like myself and ream out a Kaywoodie carb with stainless fencing wire and a Black and Decker!

    "To seek freedom is the only driving force I know. Freedom to fly off into that infinity out there."

    Posted 1 year ago #
13. 

    james
    

    Junior Member
    Joined: Apr 2011
    Posts: 71

    offline

    Login to Send PM

    This page helped me out quite a bit.

    http://www.seattlepipeclub.org/content.aspx?page_id=22&club_id=969877&module_id=16774

    Posted 1 year ago #

RSS feed for this topic

Reply

You must log in to post.

    Back To Top  | Back to Forum Home Page

   Members Online Now
   photoman13, shaintiques, lonestar, riptide, treeder13, igloo, lazydog, sergemoat, lordnoble